Packaging Certification

Audit All Three ISO Management Systems in One Go: 9001 / 14001 / 45001—Three Real Boundaries of an Integrated Audit—The Three Questions a Printing Plant Should Ask Before a Customer Audit

📅 2026-11-18 ✍️ Wuxi Lexiang Printing & Packaging ⏱ 3min read

💡 💡 At a Glance

Consolidated audits save the auditors’ time, not the printing factory’s workload. The three boundaries are the most critical: first, each certification scope is independent, so noncompliance in one scope does not affect the other two, but it does affect the customer’s judgment of the factory as a whole; second, nonconformities are documented separately for each system, so a single page may violate all three sets of standards simultaneously; third, switching certification agencies requires a new conversion audit, and certificates do not carry over automatically. When receiving notice of an on-site audit, first ask these three questions clearly.

At the end of September, a printing factory that produces export folding cartons received notice from a customer: inspectors would visit next Wednesday to audit the factory, accompanied by auditors from a third-party certification body.

The factory’s quality manager called me and said: “We’ve maintained all three management systems—9001, 14001, and 45001—for eight years. Can we have them audited all at once?”

I put it more directly:A combined audit saves the auditors a few laps around your workshop; it doesn’t save the printing factory any work.Moreover, integrated audits have three boundaries. If you don’t understand them clearly, the customer’s audit conclusions may look even worse than separate audits would.

The first boundary: the three signs on the wall represent three separate certificates, each with its own independent scope.

The most common misunderstanding is interpreting “We have ISO 9001, 14001, and 45001” as meaning we hold a single integrated certificate. In reality, they are three independent certificates, each with its owncertification scope.—9001 covers quality management, 14001 covers the environmental management system, and 45001 covers occupational health and safety management. The three certificates contain three different scope descriptions.

The key point is that the scope is not an abstract set of provisions; it can be applied to specific tasks. Here is a real example: a printing plant may describe its 9001 scope as “paper packaging printing,” while its 14001 scope may say only “the production and office premises of a paper packaging printing plant.” If the 45001 scope does not include warehouse sorting and handling positions, an auditor has no basis under the 45001 certificateto determine that you are nonconforming.—However, they will document it and remind you that the scope needs to be revised.

Therefore, the first practical step on the day of the integrated audit is to place the scopes of the three certificates side by side on the table and read through them word by word. If a task is not covered by the scope, none of the three certificates will protect you if something goes wrong. If the scope is narrower than the actual operations, it means that part of your business is “running exposed”—and anyone checking your certificates will immediately see it.

What customers usually care about most during a factory audit is not “Do you have certificates?” but rather “Does this certificate cover my order?” The printing plant should conduct this check as soon as it receives the audit notice, rather than waiting until the auditor arrives and then searching through the documents.

The second type of boundary: nonconformities are issued separately under each management system, so the same issue can result in three notices.

An integrated audit may sound like “one audit covering three things,” but when an auditor encounters a problem on the workshop floor, they must assess it separately against all three management systems.

Here is an example of something that happens every day in a printing plant but falls under all three management systems:Waste ink drums lack classification labelsand are mixed in with piles of cleaning rags.

Under ISO 14001, this concerns the environmental management system—whether waste sorting, labeling, and temporary storage are properly controlled. Under ISO 45001, it concerns occupational health—whether there are occupational health risk assessments and protective requirements for employees handling the waste. Under ISO 9001, if the plant has a document requiring “isolation of nonconforming products identified during first-article inspection,” and this waste is piled up next to the isolation area, then this isa failure to control labeling and nonconforming product management..

The same fact on the floor may result in an auditor issuing a nonconformity under each of the three systems. They are listed separately because each nonconformity must be linked to its respective corrective action requirements, remediation period, and verification method.

The practical impact on a printing plant is that the corrective action workload is cumulative, not shared. The corrective action reports must also be prepared and verified separately for each system. An integrated audit can indeed save the auditors three separate visits, but it does not reduce the plant’s own workload for documentation, corrective action, and verification at all—in fact, many plants feel more exhausted after an integrated audit precisely because of this.

Third boundary: changing certification bodies does not automatically carry over the certificate

The third boundary occurs less often, but once it does, the entire badge enters a blank period.

The validity of a certification certificate is tied to theissuing bodyandscope of coverageof the certificate. When the certification body changes, the existing certificate cannot be transferred automatically. The new body must either conduct a conversion review (usually a document review plus an on-site spot check) or perform a new initial certification under its own procedures. There is a time lag in between.

An even more troublesome issue is the chain reaction of “any change invalidates the certificate”: if the factory changes its address, adds a new product line, or expands its business scope beyond the certificate’s coverage, the certification body may require suspension or revocation of the certificate for the relevant scope. If a certificate is suspended because of a change to a single production line, customers will receive a notice that the certificate is invalid.

I’ve seen this happen for real: a printing plant added a prepress line on the second floor, which administratively counted as a “change to the production facility,” but they did not report it voluntarily. As a result, when the client conducted an audit, the auditor glanced at the plant layout and asked what was on the second floor. That single question exposed a gap in the validity of the certificate.

Therefore, the practical recommendation for the third type of boundary is simple:Proactively report to the certification body any change that could affect the scope of the certificate,even if it is just one production line, a warehouse, or a new type of customer. Proactive reporting is change management; being found out after the fact results in a nonconformity.

The three questions the printing plant should ask first upon receiving notice of an audit

When the client says they are coming to audit, the printing plant’s likely response is merely, “Okay, we’re ready,” which will probably leave them at a loss on the day. The three questions that really should be clarified first are:

The first question:“What scope will this audit cover?”——Are the three systems audited together, or only 9001? If the customer is only concerned about quality, the printing plant should not voluntarily disclose 14001 and 45001 as well, or the auditor will have many more sites to inspect that would otherwise be unnecessary, increasing the risk of discovering more issues. This point must be thought through carefully before answering.

The second question:“Can we get the customer’s own audit checklist in advance?”——When European and American customers conduct social responsibility audits using standards such as BSCI and SEDEX, they usually bring their own checklist, whose focus does not entirely overlap with the ISO systems. Obtaining it in advance allows the corresponding records to be prepared in the same folder rather than searched for on-site.

The third question:“Will we be able to obtain written confirmation of the results this time?”——If the on-site assessment is only given verbally as “largely compliant,” there will be no basis for corrective action afterward, nor any documented evidence. If the customer’s factory audit report cannot be obtained, it means the audit existed only within the customer’s internal system. At the very least, the printing plant should receive a written record that cannot serve as a basis for action but can be used to compare findings and guide improvements.

After asking these three questions, the printing plant can decide how to prepare that day. Eight years’ worth of records for three systems cannot be completed in a single day, butClarifying these three questions can prevent a full day’s preparation from being wasted..

Further reading

These articles can help you straighten out the relationships among the systems:

#Packaging Certification #ISO Certification #Integrated Audit #ISO 9001 #ISO 14001 #ISO 45001 #Management System Certification

FAQ

Can ISO 9001, 14001, and 45001 be audited at the same time, and will the certificates be one or three?

Three separate certificates, each specifying its scope of certification. The integrated audit merely arranges the audits of the three systems within the same period and completes them in a single on-site assessment. There are still three certificates, each independently valid and subject to its own expiration conditions. Audit reports are also usually issued separately for each system.

Is a consolidated review less hassle than reviewing the three systems separately?

This is convenient for the auditor, but limited for the printing plant. The auditor can make fewer visits, and some preparatory work can be shared; however, nonconformities are recorded separately for each system. The same site condition may result in one nonconformity under each of the 14001, 45001, and 9001 standards, so the workload for documenting, correcting, and verifying them adds up.

If a new production line is added or the workshop is changed, is the certificate still valid?

It should be checked whether the certified scope stated in the certificate has been exceeded or changed. Routine adjustments within the scope generally pose no issue; however, adding production sites, introducing new product lines, or expanding the business scope may constitute changes requiring notification to the certification body. If an auditor determines that the scope has been exceeded without an approved change, the relevant scope of the certificate may be suspended or withdrawn.

If the certification body has changed, can the original ISO certificate still be used directly?

It cannot be automatically renewed. New issuing bodies generally require a conversion review or a new initial certification, with a time gap in between. The certificate issued by the original body remains valid until the new body completes the conversion, but you should confirm in advance which body's certificate the client accepts to avoid a period without a valid certificate during the handover.

Does the printing plant need written documentation if the customer only says “basically compliant” during the factory audit?

Needed. A verbal conclusion cannot serve as a basis for corrective action or leave a record of the improvement process. Before the audit, the printing factory should clarify with the customer whether written records or the customer's own audit checklist can be obtained. Even if the conclusion is not used as a certification basis, it can serve as a benchmark for internal improvement.

Need a Custom Packaging Solution?

Learn more about packaging, or consult directly for a custom solution and quote