Digital printing

Digital Printing on Film Substrates: 3 Real-World Limits — Corona Treatment Decay, Adhesion Testing, and the Heat-Sealing Window — The First 3 Numbers Printers Should Ask for Film Orders

📅 2026-11-11 ✍️ Wuxi Lexiang Printing & Packaging ⏱ 3min read

💡 💡 At a Glance

3 real-world limits of digital inkjet printing on film: First, corona treatment decay—PET, BOPP, PE, and other films have inherently low surface energy and must undergo corona treatment to carry ink. The treatment value decays over time as storage temperature and humidity change, reducing adhesion and causing print samples that initially pass to delaminate completely after several days or shipment to a humid southern environment. Higher treatment intensity provides greater initial strength but faster decay, so printers must ask for the film’s production date and post-arrival storage conditions. Second, adhesion-testing limits—passing a masking tape test does not mean a label will work. Films require peel-strength testing and post-aging retesting because they become brittle outdoors or in cold-chain environments. Test standards, sampling locations, and resting times after curing must be specified. Third, heat-sealing-window limits—film has a narrow heat-sealing temperature range. Excessive temperature causes blocking and wrinkling, while insufficient temperature causes weak seals. Sealing strength is also affected by pressure, cooling time, and the film’s actual moisture condition. The first 3 numbers printers should request are the film’s production date and storage duration after corona treatment, the required adhesion level and test method, and the heat-sealing method and permitted temperature window.

In May 2026, a customer manufacturing pet products approached a printer to produce a batch of OPP film labels for packaging used on outdoor pet products.

Everything looked normal during proofing. The operator pulled a piece of tape over the ink and said, “It’s pretty secure.” The customer approved the proof, and 3000 labels went into production.

After the goods arrived at a warehouse in South China, the warehouse reported 10 days later: “The ink has come off across the entire surface of this batch of labels. It comes off with a single touch.”

The customer’s first reaction was: “Didn’t you test it during proofing?”

The printer was equally frustrated: “It was secure at the time.”

Neither person was wrong. What changed between proofing and production was not the printer’s workmanship; the surface condition of the film had changed. In digital printing on film, this occurs on virtually every order, but it was particularly pronounced in this case.

First Limit: Corona Treatment — Whether Film Can Be Printed Depends on a Certificate That Expires

Films such as PET, BOPP, and PE are chemically nonpolar. Ink consists of polar molecules. To bond the two, the film surface must be modified to introduce polar groups. This is corona treatment: the film surface is exposed to high-voltage corona discharge, which creates polar groups in the molecular chains. The treated surface energy increases, allowing the ink to adhere.

The key fact is: corona treatment is not permanent. The treatment value decays over time, with the decay rate determined by 3 factors:

  • Time. A common industry rule of thumb is that treated film retains its effectiveness for a period measured in months under standard temperature and humidity conditions. The longer it is stored, the lower its adhesion and heat-sealing strength become.
  • Temperature. The higher the temperature, the faster the decay. A roll of film taken from a southern warehouse in summer can be in a completely different condition from the same batch stored in a northern warehouse.
  • Humidity. In high-humidity environments, polar groups are more likely to migrate and rearrange. At a macroscopic level, this appears as a reduction in surface energy.

This produces a counterintuitive rule: the higher the treatment intensity, the better the initial adhesion, but the faster the decay. Film suppliers often treat the film more aggressively to ensure acceptable printability when it leaves the factory. As a result, a batch may arrive at the printer in excellent condition but lose adhesion faster after 3 or 4 months than a more lightly treated batch.

The first of the 3 numbers a printer should ask for when accepting a film order is: the film’s production date, the elapsed time between production and printing, and the storage conditions during that period. These 3 numbers indicate whether the surface condition remains within a usable range when the film reaches the press.

If the answer is, “This film has been stored for 6 months,” the professional approach is to conduct a surface-energy test before printing, using a surface-energy test pen and standard liquids, rather than starting the press immediately. If the result is unsatisfactory, either have the supplier re-treat the film or replace it with a different batch.

There is another rule: do not unroll the film at the printer before it is needed. Unrolling exposes a new surface and starts a new treatment-decay window. The recommended practice is to use film in production order, printing the oldest film first rather than searching the warehouse for the oldest roll simply to consolidate work on one press.

Second Limit: Adhesion Testing — Pulling a Strip of Tape Does Not Count

The most commonly used adhesion check inside a printing plant is the masking tape test: apply a strip of tape to the ink film, pull it firmly, and observe whether any ink comes off. This method is fast, inexpensive, and suitable for in-house inspection, but it tests only one weak condition.

It has at least 3 limitations:

  • It tests crosswise peel rather than overall adhesion. The tape acts on only a small area, while the film as a whole may still be pulled off.
  • It has almost no discriminating power for films. Many films pass the tape test immediately after printing because the ink film has not fully cured or the film still has residual stress. Actual use involves repeatedly bending the entire label, exposing it to water, and bringing it into contact with oils and fats.
  • It does not test aging. Film becomes brittle outdoors, in cold-chain environments, and inside summer vehicles, while the ink film also ages. Adhesion changes accordingly.

A more reliable approach is to conduct a peel-strength test, or a 180° fold test, according to the customer’s requirements, while clearly defining 3 conditions:

  1. Sampling location. Take samples from the cross-direction cut, longitudinal cut, and curved transition area of the ink film. The transition area experiences the greatest stress and is the most likely failure point.
  2. Resting time after curing. The strength of a freshly printed ink film is not the same as its strength after 48 hours. The test method must specify whether testing occurs 24 hours or 7 days after printing.
  3. Test environment. Testing after conditional aging, such as thermal cycling or damp heat, is closer to actual use. This step is frequently omitted from specifications and is a common source of failures in outdoor and cold-chain applications.

A practical, low-cost supplementary method is to retain first-article samples for physical flex testing: wind the printed film label around a bottle or container of the specified diameter, bend it repeatedly, and check whether the edges peel or crack. For film labels used on pet products, cosmetic flexible packaging, and personal-care products, this test is more representative of actual customer use than the tape test.

One printer added a field to its film-order specification sheet: “Adhesion requirements: □ Tape test □ Peel strength ≥ ___ N/25mm □ Retest after ___ thermal cycles □ Flex test with no peeling after ___ cycles”, allowing the customer to make selections. This form made customers realize for the first time that “I need labels that will work” and “I need labels that pass a tape test” are not the same thing. The rework rate declined markedly.

Third Limit: The Heat-Sealing Window — The Sealing Temperature Range Is Narrower Than Expected

After the film packaging is printed, it still has to be sealed. Heat sealing may appear to be the simplest operation, but it is actually one of the most failure-prone steps in film printing because heat sealing is a window, not a single point.

3 variables change simultaneously:

  • Temperature. The sealing layer, usually PE or a copolymer layer applied to the film, must reach its melting temperature to form a secure seal. If the temperature is too low, the seal is weak and opens when pulled. If it is too high, the sealing layer may overmelt, migrate onto the printed surface, and cause blocking, wrinkling, or character smearing. The heat-sealing window for film is usually much narrower than that of PE bags.
  • Pressure. Insufficient pressure leaves unsealed channels along the edges, while excessive pressure may damage the film.
  • Cooling time. If labels are stacked immediately after sealing, before the sealing layer has fully cooled, they may block together, a problem commonly known as “seal blocking.” When customers receive a stack of labels stuck together, this is usually the cause.

Another frequently overlooked variable is the moisture condition of the film. Film itself does not absorb much moisture, but the condition of its heat-sealing layer and the roll as a whole is affected by the environment. In high-humidity conditions, both sealing strength and the position of the sealing window shift. Therefore, the same heat-sealing parameters cannot be applied unchanged during the rainy season and dry winter.

When accepting a film order, printers must clarify 3 details concerning heat sealing: what equipment will perform the sealing, such as a continuous sealer, an intermittent sealer, or the customer’s own equipment; the permitted heat-sealing temperature range, as tested on the customer’s equipment; and how the labels will be stacked after sealing and the maximum stacking time, which determines cooling-time requirements.

If the customer performs the sealing, the printer’s responsibility ends with the heat resistance of the ink film at delivery. During heat sealing on the customer’s equipment, will the ink layer soften, distort, or change colour? Heat resistance should be validated by the printer using the customer’s temperature parameters on samples, rather than being discovered only when the customer begins mass production.

The First 3 Numbers a Printer Should Ask for a Digital Film-Printing Order

Information to requestWhat to askWhy it determines feasibility
Film production date + time stored at the printer + storage conditionsWhether the film is customer-supplied or purchased by the printer, how long ago it was produced, and the temperature and humidity conditions under which it has been storedDirectly determines whether the corona treatment value remains within a usable range and whether the film must be re-treated or replaced
Required adhesion level and test methodThe customer’s validation method: peel strength or tape testing, and whether retesting after aging is requiredDifferent test methods can produce completely opposite conclusions for the same batch. Without clear requirements, the printer and customer may dispute the acceptance results
Heat-sealing method + temperature window + cooling timeWho performs the sealing, what equipment is used, the permitted temperature range, and how the labels are stacked afterwardThe heat-sealing window is narrow: excessive temperature causes smearing, while insufficient cooling causes blocking. Both issues are attributed to the printer’s delivery quality

Once these 3 numbers are established, the printer should conduct a heat-sealing trial on the customer’s actual sealing equipment during proofing, rather than using the printer’s own equipment, and should test under at least 2 environmental conditions, such as standard temperature and humidity and high temperature and high humidity. The position of the heat-sealing window shifts under different environmental conditions, so parameters established in the printer’s workshop may not remain valid at the customer’s facility.

Returning to the ink-delamination case, the post-mortem conclusions were clear: the OPP film remained in the printer’s workshop for only 9 days, testing was conducted at the printer, and the goods spent a period in a high-temperature, high-humidity environment after shipment to a warehouse in South China. After the film’s surface treatment value had decayed, the ink film lost its bonding ability. The printer did not violate any procedures, but it had asked for one fewer number and omitted one environmental validation.

The real threshold for digital printing on film lies not in printhead precision, but in understanding a material surface with a limited service life. Once these 3 numbers have been clarified, most delamination and sealing failures can be resolved before the press starts running.

Further Reading

#film printing #corona treatment #adhesion testing #heat-sealing window #digital inkjet #surface energy

FAQ

How long does corona treatment remain effective?

There is no fixed answer because it changes over time and with the environment. A common industry rule of thumb is a period measured in months under standard temperature and humidity conditions. The specific performance is affected by 3 factors: the longer the storage time, the greater the decay; the higher the temperature, the faster the decay; and the greater the humidity, the more noticeable it becomes. One counterintuitive point is that higher treatment intensity produces better initial adhesion but also causes faster decay. Suppliers often treat film more aggressively to ensure printability when it leaves the factory. Therefore, printers should ask for the film’s production date, the time it has been stored after arrival, and the storage conditions. When necessary, they should test surface energy with a surface-energy test pen before printing rather than starting the press immediately.

If a label passes the tape test, can its adhesion be considered qualified?

It can only be said to have passed the tape test. This method measures a small-area crosswise peel and has almost no discriminating power for films. Many films pass immediately after printing because the ink has not fully cured and the film still has residual stress. To obtain a result that reflects actual customer use, peel-strength testing is needed, with clear requirements for the sampling location, including cross-direction cuts, longitudinal cuts, and curved transition areas; the resting time after printing, as 24 hours and 7 days represent different conditions; and whether retesting after conditional aging is required. Outdoor and cold-chain applications must include post-aging retesting, otherwise the test has little practical value.

The film printed correctly, but the image became smeared during heat sealing on the customer’s machine. Who is responsible?

It depends on how responsibility is defined. If the customer performs the sealing, the printer is responsible for the heat resistance of the ink film at delivery. The printer should therefore have validated samples beforehand using the customer’s temperature parameters rather than waiting for the customer’s mass production. If the customer provided no sealing parameters and did not accept the printer’s heat-resistance validation, the printer is not responsible for this issue; instead, the customer is responsible for not specifying the conditions of use. The safest approach is to include 3 items in the specification sheet: the sealing equipment model, the permitted heat-sealing temperature range, and whether the printer will conduct heat-resistance validation, together with the results.

Why does adhesion vary within the same batch of film?

The most common reason is uneven corona treatment values within the roll. Treatment is performed during unwinding or rewinding, and dwell time within the roll, unwinding speed during treatment, and workshop temperature and humidity can all create differences along the roll direction. Two secondary factors can also play a role: minor print-grade surface defects on the film, such as residual mould-release agent or dust attracted by static electricity, may reduce local adhesion; and uneven ink-film thickness can cause the thinnest areas to fail first. To investigate, samples should be taken from the affected locations for surface-energy and peel-strength testing, with each section of the roll ruled out one by one. For prevention, the most effective measures are controlled storage and press-running sequence, with the oldest film used first.

Does ink delamination from a film label necessarily indicate an ink-quality problem?

Not necessarily. Delamination usually has 3 levels of causes. The first is decay of the surface treatment, which is the most common, especially after storage in a high-temperature, high-humidity environment. The second is chemical compatibility between the ink film and the film, as inkjet inks have different surface-tension and surface-condition requirements for different films. The third is the ink itself, including poor pigment dispersion, insufficient curing, or an abnormal batch. The troubleshooting sequence should be: first test surface energy to determine whether the treatment value remains within a usable range; then examine ink-film thickness and curing conditions; and only then question the ink batch. Reversing this sequence by replacing the ink before testing surface energy often wastes money because ink was not the cause.

Need a Custom Packaging Solution?

Learn more about packaging, or consult directly for a custom solution and quote